Ormus Minerals ORMUS Formulas Imprinted Ormus Formulas Ormus Minerals TOP SELLERS Ormus Minerals NEW Products Ormus Minerals Store Ormus Minerals Questions Contact Us

Ormus Wet Method

Chapter 5
How to get Ormus into your life today
There's no doubt if we had to choose a Ormus extraction method that is possible at home with minimal equipment and skill that produces a high quality Ormus end product it would have to be the Ormus wet method. The Ormus wet method, while not simple, doesn't require a chemistry degree to execute properly and is relatively safe in most cases as far as we know, as long as the instructions are followed.

Please be aware the key words are "relatively safe in most cases as far as we know." The science of Ormus is an ongoing process and in many ways though we think we understand how it works and operates and there is substantial evidence the Ormus wet method is safe, there are still many unanswered questions.

Hopefully in the months and years ahead these questions will be answered in hard scientific studies.

All that said let's explore the Ormus Wet Method.

The Ormus Wet Method Instructions

What you'll need:

Dead Sea Salt
Food Grade Lye Granules
Distilled Water
Coffee Filters
PH Probe

How to get Ormus into your life today
Step 1: The first thing we need to do is use our food grade lye granules and distilled water to make lye solutions. Please pay close attention while doing this getting it right is very, very important unless you'd like a contaminated product at the end.

Next you add ½ a cup of the food grade lye granules to a quart of your distilled water. Be sure you are doing this under your hood vent of your stove or even better outside. The fumes are dangerous and you definitely don't want to breathe them in unnecessarily, they can cause serious and potentially permanent harm. Gloves and a mask are a must. Be sure you are adding the lye granules to the water and not the other way around this is also very important.

Stir as you SLOWLY add granules to the distilled water. The solution is going to heat up and become misty looking. This is normal and to be expected. When it cools it will go back to looking like plain water. This is very important to note. The last thing you want is to have someone confuse your lye solution for plain water. Put your finished lye solution in a glass or plastic container (never, ever use metal) and label it as lye solution immediately.

Safety should always come first. We make Ormus to enhance our health not endanger it!

Step 2: Now we want to rehydrate our Dead Sea salt. The ratio we are using is ½ a cup of Dead Sea salts (the higher quality the better) to 1 cup of distilled water. You have lots of options to do this easily including buying a plastic measuring bowl and simply adding the proper amounts of Dead Sea salt and distilled water. Stir well, of course, until the salts have all completely dissolved.

Step 3: Filter your re hydrated Dead Sea salt water through your coffee filters. This is to be sure there are no rocks or other elements beyond Dead Sea salt in the water that could be harmful or toxic when you separate the Ormus materials.

Step 4: Now comes the fun part! We're ready to do our precipitation. Place you PH probe into the Dead Sea salt water and turn it on. This is where it will be for the entire precipitation process. Keep an eye on the PH and start stirring? It should be in the 7.5 to 8.5 PH range.

Don't stop stirring and add your lye solution one small squirt at a time. It's very important you add the lye solution slowly and while continuing to stir. Don't be tempted to try to speed up the process, or you will likely be very unhappy with the results!

Now the key here is to add a little lye solution, watch the PH meter move, and then wait for it to stabilize while stirring before you add another squirt of lye solution. You will do this many times until you notice the PH meter is no longer moving as quickly despite your adding more lye solution. This area is where most of your Ormus materials are being made. Continue adding the lye solution squirt by squirt and stirring at the same steady rate. Once you see the PH begin to jump again. In most case you can expect your PH to be around the 10.2 or 10.3 mark, but this can vary depending on all sorts of conditions many of which we can't control.

Now we never want our PH to rise above 10.78. When it stabilizes in the neighborhood of 10.6 we are ready. This whole step should take about thirty minutes so be prepared to stir or have a partner help you out.

Once you have maintained for a while at 10.6 cover in plastic wrap and let sit for a full 24 hours.
How to get Ormus into your life today
Step 5: Now 24 hours later you should have roughly 350ml of milky precipitation at the bottom of your container. All the rest should be clear water. Slowly, and careful pour off  the top clear water WITHOUT disturbing the precipitation beneath.  If you accidentally mix it together you are going to have to let it settle again for another 24 hours.

Step 6: Time to wash the precipitation. You will add the same amount of distilled water to the precipitation as you have precipitation. So if you have 350ml you add 350ml of water. Simple right? Allow to settle for 24 hours, pour off and add at a 1:1 ration again. You will do this a total of three times. What's left is your "washed" precipitation.

Step 7: Now that your Ormus precipitation has been washed simply add the same amount of distilled water to it again and bottle it. It is now ready for use! Pretty exciting isn't it? After you are near a week of work you are ready to start getting the benefits of the Ormus materials.

What's the proper dosage for the Ormus materials made using this Ormus wet method?

Good question. After dosing the material in step 7 most of those in the know suggest starting with ½ tsp. a day on an empty stomach and moving up once you can judge how well your body responds to it. Less if often more with Ormus, so be cautious! Don't forget, once again, safety always come first.  

How to get Ormus into your life today

Regardless of how our products may be used in other countries, or anything that you may have heard or read about Ormus Minerals or Ormus products, under FDA law in the United States it is illegal for a manufacturer to make any medical claims for health supplements. None of the products offered for sale on our website or direct to retail consumers are intended to be used in the treatment or mitigation of any disease state. All statements made by Ormus Minerals or on the Ormus website are intended for informational purposes only. The statements made here have not been evaluated by the FDA, and our products are not intended to diagnose, treat, cure or prevent any disease. Health decisions are much too important to be made without the advice of a health care practitioner. As with any dietary or herbal supplement, you should advise your health care practitioner of the use of this product. If you are nursing, pregnant, or considering pregnancy, you should consult your health care practitioner prior to using any health supplement product.